57DP-12-2C2 RELAY PDF

RELAY 57DP 1C6 24V. RELAY 57DP 1C6 6V. RELAY 57DP 1C/O 24V OEN. RELAY 57DP2C2 12V. RELAY 57DP 2C2 16V. RELAY 57DP 2C6 24V. RELAY. Supply Of Oen Relay 57DpV-2C Make- Oen/Pla/Omron. Details As Per Annexure-A. | Due date: 28 Jun, | Tender work Value. 57DPB2 57DPB6 57DPA2 57DPA6 57DPC2 57DPC6 57DPA2 57DPC2 57DPC6 57DPC2 57DPC6 57DPB2 57DPB6 Description, MINIATURE POWER RELAYS.

Author: Nikotilar Zologar
Country: Switzerland
Language: English (Spanish)
Genre: Relationship
Published (Last): 19 August 2014
Pages: 329
PDF File Size: 19.14 Mb
ePub File Size: 17.56 Mb
ISBN: 250-7-14248-774-2
Downloads: 13406
Price: Free* [*Free Regsitration Required]
Uploader: Kigul

Some are running at lower priorities and can be interrupted requiring more than one relag interval to complete a task. If this bit is set to 0, the user will not be given G08 as an option when programming block functions. Once an axis is disabled, the user can no longer program a NC block with that axis until it is enabled once again.

Velocity Ramp for E-Stop Bit 6: Because of this, if the same position is programmed in successive blocks, each block executed will result in the spindle moving to the programmed position, even if the programmed position is the same for each block. Zero Offsets are used to temporarily change axis offsets, as an aid to simplify part programming for multiple parts. This makes it easy for the user to view and edit the program compared 57dp-12-2×2 a compiled program method.

Rekay following time estimates may be helpful in analyzing and understanding the profiles: Tool Correction values will also be in units per table rev. If a G08 is used in a program without this parameter activated the following error appears: If an absolute move to zero degrees is commanded after that, the table would move 57dp–12-2c2 degrees.

The smoothed torque actual value is checked in the drive as to whether it has exceeded this value. If you are unsure of the formula to use, call the Indramat Service Hot Line at It also shows use of conditional jumps for selection of one of three different programs, a move to tool change position, and relxy to positive stop.

Related Posts (10)  KOTARO OSHIO TWILIGHT TAB PDF

Sign Up to Newsletter

This parameter is only effective on servo systems reoay have a multi-turn absolute feedback mounted on the servo motor. Placing a 2 here will cause the unit to always Home using the shortest path to Home. These include program block commands, read and write variables, etc.

This should be avoided. Table below shows typical values of the additional interface type number.

57DP-12-2C2

This means that this drive is now disabled, it still has control and bus voltage, but will not exert any torque on the motor shaft. If a value greater that this parameter is entered in the user program, an error will occur before the felay is executed. This value relates the velocity loop proportional gain, Kp to the velocity loop integral gain by the ratio: Thus, any auxiliary functions in this NC Block may be turned on while the axis is still in motion. Felay rapid positioning because the cam search has the higher S-x, same precision because the cam edge search has the lower P-x This reference value is used to establish the machine reference point as some point other than Home, such as the center point of the slide.

The physical width of the cam at the load must be entered in S so that the same position can be achieved regardless of the direction of search. Refer to Adaptive Depth Control G08 on page for more information.

If the parameter you are writing to is a Hex value a set of 16 bits,you must send the complete bit pattern for the entire parameter. Also, the higher the intermittent current level, the less time available for peak current.

Note that drive parameter S Bipolar Velocity Limit Value is determined by the maximum speed of the motor and any limitations due to the mechanical characteristics of the axis. During the time that the G21 command is in operation, no movements should be commanded, otherwise an error will appear on the display, resulting in a fault.

The S3 high switch is the first digit and the S2 low switch is the second digit.

Related Posts (10)  GRUNDFOS MAGNA 25-40 PDF

57DPC6 pdf Datasheet P1 Part Num IC-ON-LINE

To determine if the value entered in this parameter is correct, 57pd-12-2c2 off a known distance on the machine slide and jog the axis that distance. No tool correction programmed 8.

G69 is intended for machine commissioning and repair only, and therefore should not be used to temporarily change axis co-ordinates. In order to assure relxy measuring references, programs which use zero offset referenced measurements must be started with a homing instruction which sets the corresponding zero offset.

It occurs when the system is running the program and the enable goes low. See applications description of AC main spindle drives for functional description and programming. This value will be the speed used to position the spindle when it is commanded in a program block.

If the threshold is exceeded, then bit 7 of S class 3 diagnosticsis set to 1, and, once the value drops below the threshold, cleared.

If set to a 1, with a power failure, the TRANS D controls the stoppage of the spindle motor using the appropriate command values. Once the units are repay configured 57dp-122c2 Aa02 for all axes, returning to this screen will show the correct acceleration units. If an extra measure of data checking is desired, the value can be read back from the TRANS D by sending only the header without a value and comparing with the value that was sent. All subsequent parameters that relate to speeds and positions must be re-entered.

B Interbus Fieldbus Interface C. If incremental moves are required after a move 57dp-122-c2 positive stop, they should be preceded by an absolute move to the last position, to correct for any shift in position during clamping. These signals are the: The CTA unit requires a 24Vdc supply, and is designed to be a dedicated operator panel mounted outside the system cabinet.