Eemax EMT6 – EMT6 Mini Tank Water Heater V, 6 Gallon – FEATURES EMT6 must be hardwired Point-of-use heating eliminates long hot water pipe runs. Electric Mini Tank Water Heaters EMT1 – EMT – EMT4 – EMT6 Installation and Operating Instruction Manual Table of Contents Important Safety Instructions. Get Eemax EMT6 Instructions / Assembly. Get all Eemax manuals!.

Author: Mut Kazragore
Country: Sierra Leone
Language: English (Spanish)
Genre: Photos
Published (Last): 26 July 2017
Pages: 151
PDF File Size: 1.67 Mb
ePub File Size: 2.97 Mb
ISBN: 807-1-47072-360-2
Downloads: 71486
Price: Free* [*Free Regsitration Required]
Uploader: Dagrel

What’s missing? Tell us about it.

The pressure vessel water tank is welded, glass lined steel and is equipped with an anode rod. Must not have a shut off valve between relief valve and tank or relief valve and termination of discharge.

Install or locate this water heater only in accordance with the provided installation instructions. Avoid damaging the wemax of the element. Install new thermostat, attach wires and tighten screws. No Dual Lav Model Available: Reasonably priced hot water heater Your review: If hydrogen gas is present, there will probably be an unusual sound such as air escaping through the faucet as the water begins to flow.

EMT models can be installed under the sink. Pre-heated or Cold water Inlet Aerator Supplied: Install a PSI pressure relief valve in the cold water supply line. The water heater is equipped with an adjustable thermostat that once set will automatically control water temperature. Manufacturer is not liable under this limited warranty or otherwise if: Power is automatically turned off to the heating element.


Water is too hot 1.

If no receptacle is available adjacent to the water heater, contact a qualified electrician to have one properly installed. Install a pressure reducing valve if your water pressure is greater than psi. EMT models can replace traditional central hot water heaters thereby conserving water and reducing energy waste. The water heaters are very reliable a good quality product.

The element can be descaled chemically or manually. Indicator light not on 1.

EemaX EMT6 Instruction manual |

Stiebel Eltron Mini 1. Check entire system for leaks. Always unplug the power supply cord when the water is turned off or when servicing or draining the water heater. You are now ready emax use your water heater. No Tepid Water Model Available: Always unplug met6 power supply cord when the water is turned off or when servicing or draining the water heater.

Must NOT be smaller in diameter than the outlet diameter of the eemaax, or have any reducing couplings.

Turn off power supply, unplug water heater power cord and drain see above. Shopping mall and Retail outlets Schools and all other public buildings Office and tenant spaces Commercial builds such as Restaurants and Service Stations Modular buildings, office and trailers Concession stands and food service locations Any remote sink that does not have hot water.


To descale chemically, demax the heating element in white vinegar or other descaling solution and then rinse well with fresh water. Sizing – Size based on performance and not electrical infrastructure. Hydrogen gas can be produced in a hot water system served by this heater that has not been used for a long period of time generally 2 weeks or more.

Turn the temperature knob counter clockwise to a lower temperature setting. Install the correct size circuit breaker into the master panel. If light does not come on, check semax the reset button is pushed in; follow steps from previous section.

Must terminate at an adequate drain. Remove heating element noting original positions of all connections. Reinstall the element and gasket.

The purpose of the aerator is to restrict the amount of water flow exiting the EMT1 which allows the water heater to produce hot water for a longer duration. Insure that the water heater is installed in a level position. Comply with the Installation Instructions before connecting to electrical eeamx. Turn off the cold water supply to the water heater.

Before calling for service, first confirm that the water heater is properly filled and that VAC power has not been interrupted. Top Hot or Cold Feed: