KANTECH KT 300 PDF

The Combus is a communication protocol that is integral to the KT It uses a four-conductor cable bus to which several expansion modules can be. Controls two doors and easily links to a network Update firmware directly from system workstation Fast operation, up to , baud Ready to go, no DIP. KANTECH SYSTEMS | KT/K Door Controller, 2-Reader, Kilobyte, ” Length x 3″ Width x ” Height, With Accessory Kit, Metal Cabinet with .

Author: Tygohn Mazujas
Country: Greece
Language: English (Spanish)
Genre: Photos
Published (Last): 3 May 2006
Pages: 317
PDF File Size: 13.51 Mb
ePub File Size: 6.86 Mb
ISBN: 142-1-91653-396-9
Downloads: 19574
Price: Free* [*Free Regsitration Required]
Uploader: Dujind

I forgot to tell you that it was hooked up and unhooked before before i started with the company and I am just rehooking it back up.

The status that is seen says controller kantecy module not assigned. After all wiring is completed, apply power to the KT Their tech support is extremely helpful. Please refer to the graphic below for a detailed view of their location. Alarm Panel Integration Kits.

I tried the above steps but got no joy. This battery must be replaced by a Kantech technician to avoid any risk of explosion. Table of Contents Pre-Installation Information Products which Kantech determines to be repairable will be repaired and returned. This module allows a maximum of 16 outputs and a maximum of up to 50 katech per output. Table of Contents Add to my manuals Add. By continue to navigate through this site or by clicking Approve, you consent to the use of cookies on your device as described in our Privacy Notice.

Posted July 18, You need to be a member in order to leave a comment. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as an access control system.

Related Posts (10)  6ES7 901-3DB30-0XA0 PDF

Kantech will not accept any shipment whatsoever for which prior authoriza- tion has not been obtained. Kanfech offerings and specifications are subject to change without notice. Paying a company a couple of hundred will be well worth it.

All circuits are power limited. Posted May 29, Controllers are linked together through their RS connectors. Make an earth ground connection to the cabinet of the KT as per the requirements of your local electrical code. Installing The Kt The KT uses high performance communication, proper grounding must be provided to ensure proper operation.

Become a hattrix end user. It does not seem to be communicating with the software. Page 4 Installation and Wiring I did a hard reset the way it said to do it kantceh the manual and now all it does is flash 4 times per second hard reset to factory defaults. Become a hattrix provider. All specifications kantfch current as of publication date and are subject to change without notice.

Kantech KT-300 Installation Manual

3000 The blue heart beat lights flashes 4 times. Availability varies by region and may require certification; please verify conditions with your Regional Sales Manager. Flash memory allows for firmware updates from an EntraPass workstation in just kantecy few minutes. Do not connect the power until all wiring is completed. I have it set up to run through a usb Actual products may vary from photos. Comments to this Manuals Your Name. Posted June 16, Then, connect the AC transformer.

Thanks in advance for any help. A set fee which Kantech has pre- determined and which may be revised from time to time will be charged for each unit repaired. KT Door Controller The KT door controller supports up to two readers, which can be installed either kanttech a single door to monitor both entry and exit or on two separate doors.

Related Posts (10)  HAROLD CHERNISS PDF

Kantech Kt-300 2 Door Controller 128kb Memory Metal Cabinet

If the KT loses communication with the module, it will initiate a module reset and will power down the Combus for five seconds in an attempt to reset the problem module. Before I begin, let me tell you I do not have a lot of experience setting them up.

30

Applying Power After wiring is completed, apply power to the KT Don’t show me this message again. If a device operates only by AC power, any interruption, however brief, will render that device inoperative while it does not have power. Preferably, it should be placed at a convenient distance from the connected devices. The KT knatech high performance communication, proper grounding must be provided to ensure proper operation.

KT Door Controller

Visual Status Indicators leds 2. Overview Power kh are supervised and individually protected against short-circuits and surges by self-resetting PTC. Kt Compliance Specifications Backup battery provides operation of up to 12 hours but has been tested only 4 hours per Section 33 of UL, fifth kantsch. Stand-alone mode protects against power or system failures and the system stores cardholder and event data, which is automatically transmitted back to the EntraPass system once the network connection is restored.

To print the manual completely, please, download it. There are liability issues relating to access control such as Fire code etc. My suggestion is to call in a company to deal kantedh this. Since the KT only supports mA, a power supply module can be used to provide an additional 1 A to the Combus.