TM 9-1275 PDF

Section 1. Paragraphs INTRODUCTION. 1. Scope. a. This manual is published for the information and guidance of ordnance maintenance personnel. Carefully clean corrosion preventives from materiel received from storage (refer to TM ). b. Instructions for cleaning and lubricating the rifle by using are. Tm – US 30 cal. – Download as PDF File .pdf), Text File .txt) or read online.

Author: Kenos Mojar
Country: Lesotho
Language: English (Spanish)
Genre: Sex
Published (Last): 8 November 2005
Pages: 290
PDF File Size: 8.9 Mb
ePub File Size: 16.60 Mb
ISBN: 914-5-86552-227-7
Downloads: 91091
Price: Free* [*Free Regsitration Required]
Uploader: JoJoktilar

Replace screw and tighten as above: Earlier type rifles have a plain butt plate mounted flat on the butt -91275 without trap. If production line procedure is used, keep the barrel and receiver, the operating rod, and the bolt together. Third and fourth echelon personnel normally process materiel for use in the hands of troops and materiel to accompany troops overseas. Slight outward pull will relieve strain of turning knobs. To verify set- ting of rear sight, set the yard elevating 9-11275 graduation opposite the index line on the receiver.

This manual is published for the information and guidance of ordnance maintenance personnel. Inspect barrel for serviceability. Straps long and short. Before any attempt is rm to Inspect a barrel for serviceability, fouling and oil should be removed and the bore wiped dry. Bayonet as a unit. If production line procedure is used, keep the barrel and receiver, the operating rod, and the bolt together.

Degreasing, disassembly, refinishing, assembly, final inspection, and packaging. Check rod for burs and handle lug ym side for wear.

Related Posts (10)  HEIDEGGER RECTORIAL ADDRESS PDF

Dents in edges of blade can often be peened out before smoothing. Check lug for wear and burs. Fundamentally, rebuild of the rifles is divided into six stages: Check bayonet scabbard catch slot for deformation and burs. By referring the serviceability chart, the inspector may readily determine the serviceability of a weapon in accordance with its future disposition.

Large end of spring should be seated in clip latch and small end in seating recess in receiver. However, rifles of early and present manufacturer of the same model may differ somewhat due to changes in design of some of the component parts. Check catch notch for angle of contact with catch hook and for wear and burs.

In- ner surface of elevating knob rim 9-127 be dressed off sufficiently with sharpening stone to allow the serrations to mate. For additional information, see the Global Shipping Program terms and conditions — opens in a new window or tm 91275 lug, contacting accelerator, for burs. Check nose of hammer for wear and burs, and bolt camming surface top for roughness fig. You are covered by the eBay Money Back Guarantee if you receive an item that is not as described in the listing.

Lay tool with patch into palm of left hand, close left hand over tool, and give tool about three turns to the right.

Check spring plunger for deformation and nose for wear and tours. Check for loose or burred stock ferrule. Although parts are interchangeable, tm work best 91-275 their original combination.

TM EPUB DOWNLOAD

Loading may also be affected, as the catch will not release properly. Please enter a number tm than or equal to 1. Remove brush and run several more wet patches through the bore. The firingplncan then be with- drawn ttm its well, and new firing pin assembled, from the rear of the receiver. Check grip screw and escutcheons for looseness, wear, projection above grips, and for burs.

Related Posts (10)  TRATADO GENERAL DE SOCIOLOGIA LUIS RECASENS SICHES PDF

TM 9-1275 EPUB DOWNLOAD

Check latch for reten – tionwear and tours fig. Carbon in gas cylinder group and on piston. Trouble may be remedied by replacing trigger guard 9-125 lightly peening the lugs. Check rear sight nut for damaged or Improperly assembled nut lock, missing spring, foreign matter behind nut, and burs. Check piston for scoring and excessive carbon, and rod back of piston for rust. Check rod for binding with under side of barrel at the chamber, and at stock ferrule.

File butt tk to seat plate with close fit all around. Check screw wrench re- cess new type for wear and burs. Clean out hole thoroughly and drive plug to bottom. They are used in determining the force required to pull the trigger of the rifle. Shipping cost tm be calculated. Proper use of rifle bore cleaner is as follows: If bayonet lug is worn to loose fit with bayonet lug ways, 9-2175 looseness cannot be corrected in bayonet ways as ex- plained in paragraph 46 c.